Name of co.   

   Specification

CS14

Atlas

Copco

DEPTH CAPACITY CORING (WIRE LINE OR CONVENTIONAL):

B WIRE LINE)

1540 M (5052 FT

N WIRE LINE

1200 M (4042 FT)

H WIRE LINE

800 M (2695 FT)

P WIRE LINE

475 M (1558 FT)

DEPTH ARE BASED ON VERTICAL HOLE

MAIN HOIST:

SINGLE LINE CAPACITY:

BARE DRUM 80 KN (18 000 LB)

LINE SPEED :

BARE DRUM 44 M/MIN (148 FT/MIN)

CABLE SIZE:

35 M (118 FT) X 16 MM (10/16 IN)

WIRE LINE

CAPACITY:

1830 M (6000 FT) OF 4, 76 MM (3/16 IN)

975 M (3200 FT) OF 6, 35 MM (1/4 IN)

LINE PULL:

BARE DRUM: 11, 9 KN (2665 LB)

FULL DRUM:

3,0 KN (668 LB)

LINE SPEED:

BARE DRUM 114 M/MIN (374 FT/MIN)

FULL DRUM 453 M/MIN (1486 FT/MIN)

MAST AND FEED SYSTEM

FEED TRAVEL:

3, 5 M (11, 5 FT)

FEED SPEEDS:

FAST AND SLOW WITH VARIABLE CONTROL

THRUST:

59, 6 KN (13 390 LB)

PULL:

138 KN (31 020 LB)

DRILLING ANGLE:

45 TO 90 DEGREES

ROD PULL LENGTH:

6, 09 M (20 FT)

POWER UNIT

MANUFACTURE:

CUMMINS

MODEL:

QSB5.0-C, 5.9 LITER 6 CYLINDER

POWER:

158 KW (212 HP)

RPM:

1800

ENGINE TYPE:

DIESEL TURBOCHARGED/AFTER COOLED

COOLING:

WATER

HYDRAULIC SYSTEM

PRIMARY PUMP:

28 MPA – 242 L/MIN (4061 PSI – 63, 9 GAL/MIN)

SECONDARY PUMP:

20 MPA – 122 L/MIN (2901 PSI – 32, 2 GAL/MIN)

AUXILIARY PUMP:

21, 5 MPA – 47 L/MIN (3118 PSI – 12, 4 GAL/MIN)

COOLING:

HYDRAULIC OIL AIR

DRILL HEAD AND SPINDLE SPEEDS

POWER:

HYDRAULIC MOTOR – VARIABLE SPEED/REVERSIBLE

FINAL DRIVE:                        

4 IN CHAIN DRIVEN IN OIL BATH – 2, 5 RATIOS

SPINDLE (INNER DIAMETER):  

117 MM (4 5/8 IN)

SPINDLE SPEEDS :

RATIO SPEED, RPM TORQUE, NM (FTLB)

1ST 6, 63:

1 132-207 5113-3259 (3759-2396)

2ND 3, 17:

1 275-432 2445-1558 (1798-1146)

3RD 1, 72:

1 508-796 1326-846 (975-622)

4TH 1, 00:

1 873 1369 771-492 (567-362)

RANGE SELECTION:

MANUAL CONTROL FROM OPERATOR’S STATION

HINGED HEAD:

SWING AWAY

CHUCK ASSEMBLY

TYPE:

HYDRAULIC OPEN, SPRING CLOSED

MAXIMUM INSIDE DIAMETER:

117 MM (4 5/8 IN)

HOLDING CAPACITY:

1 8143 KG (40 000 LB)

DRILL BASE SUPPORTS

TRAILER MOUNTED RIG, FOUR 770 MM (30, 3 IN) WHEELS

SUPPORT:

4 HYDRAULIC JACKS

PAD DIAMETER:

200 / 230 MM (7, 87 / 9 IN)

TRAVEL LENGTH:

550 MM (21, 6 IN)

WEIGHT

BASE DRILL:

7000 KG (15 430 LB)

DIMENSIONS (L – W – H)

IN TRANSPORT POSITION (TOP MAST REMOVED):

6370 MM (21,45FT) 2200 MM (7,22FT) 2340 MM (7,88FT)

TRANSPORT ON DRILL SITE (TOP MAST FOLDED):

6370 MM (21,45FT) 2550 MM (8,59FT) 2340 MM (7,88FT)

STANDARD EQUIPMENT

-HYDRAULIC MAST DUMP -HYDRAULIC MAST RAISE

-MAST IN TWO SECTIONS -4 HYDRAULIC LEVELLING JACKS

-LARGE CROWN SHEAVE WHEEL -TIER II ENGINE

-TOWING PACKAGE -WEAR LINES ON LOWER MAST

-FUEL TANK 200 L (53 GAL) -SAFETY GUARDS

-HYDRAULIC OIL RESERVOIR FILL -FUEL FILTER & WATER SEPARATOR PUMP & FILTRATION

OPTIONS

-HYDRAULIC P-SIZE ROD HOLDER -HYDRAULIC MUD MIXER

-MAST LIGHTENING KIT -WATER FLOW METER

-RPM METER -HYDRAULIC BREAK OUT TOOL

-HYDRAULIC MUD PUMP, TRIDO 140:

MAX FLOW:

140 L/MIN (37 GAL/MIN)

MAX PRESSURE:

7 MPA (1015 PSI)